Jump to content
forum-okna.ru

Recommended Posts

Posted

Всем доброго времени суток. Проблема такова. Рамкогиб гнет только одну строчку из задания и зависает с надписью на фото. Ни на одну кнопку на панели не реагирует. При этом в панель можно загрузить новое задание через лифрейм на втором компьютере, но больше ничего не происходит. После перезагрузки новое задание отображается в ордере. И снова согнуть можно только одну строчку. 

IMG_20260928_160243.jpg

  • 2 weeks later...


Оконный портал tybet.ru | Подписка на новости | Бесплатные объявления | Наша телега | База оконных знаний | ОНЛАЙН-ВЫСТАВКА



Posted

проверьте срабатывание педали, может быть сломался концевик.

  • Like 1
Posted

Педаль работает. при запуске задания станок ждет подтверждения запуска нажатием педали. После окончания изгибания рамки она зажата в станке, после нажатия педали он рамку отпускает и её можно забрать. 

  • 2 weeks later...
Posted

Доброго времени суток! Если нажать кнопку select start и следом enter без выбора диапазона резки, то после гнутья 1 позиции Рамкогиб  зависает с надписью на фото. Если после нажатия select start выбрать диапазон резки (1 или 1-5 или 3,4) то рамкогиб всё отрабатывает и не зависает.

Posted
В 27.10.2026 в 07:43, Сергей_62 сказал:

Если нажать кнопку select start и следом enter без выбора диапазона резки, то после гнутья 1 позиции Рамкогиб  зависает с надписью на фото.

если не нажимать F6 - select start - а просто нажимать педаль, то станок должен изгибать все рамки задания подряд. Читатйте инструкцию по эксплуатации. Компьютерщики по этому поводу 20 лет пишут RTFM - read this fucking manual!

Posted

если не нажимать F6 - select start и нажать педаль, то вообще ничего не происходит. даже если нажать F6 - select start,  не нажимая затем enter,  тоже ничего не происходит после нажатия педали.

Posted

As soon as the spacers are inserted, the right bending die is mounted, the plug-in mould
for the particular profile adjusted and the mould closed by hand-valve, the automatic sequence
is started.
By pressing the foot button the profile is transported to the bending head. The 1st corner
is bent after 75 mm. Then the profile is transported through the bending area and the other
corners are bent one after the other. The saw cuts the spacer to the required length according
to the particular reduction values.
The finished frame is removed by hand and the foot button is pressed at the same time to
start the next bending process. At sizes larger than 2 200 mm x 1 200 mm the frames are
produced in 2 u-shaped pieces. They are connected with 2 straight keys to finish the
frame.

When input is finished:
home- key
The monitor shows the request for the items to be processed.
If one particular item shall be processed:
- enter item no.
key E
The monitor shows the working mode with quantity of profiles to be processed and the
spacer bar length (in mm). In this mode the automatic process for frame manufacturing
can be started.
If any particular items shall be selected:
key "F6 - select start"
Enter desired items (no special sequence required).
e.g. 1 - 5 8 - 10 25 - 15
The monitor shows the working mode. The item to be processed is clearly shown by high
appearance of the respective line.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.